Ethernet I/O module Modbus/TCP / UDP slave
1 x RJ45 Ethernet
Redundant Power Supply
Protocol: TCP, UDP, HTTP, DHCP, BOOTP and TFTP
Web configuration and firmware update via Ethernet
2 x digital input (Wet - volts supplied)
2 x Relay, COM, NO - 250VAC 5A, 30VDC 5A
Avoid inductive load to relay contacts
With locked DI and 32-bit 3.5kHz counter
With I/O pair - input is mirrored in the other's output
Dual-watchdog with Power-on-safe value
Supply voltage: 12 - 48VDC, 1.7 Watt
Dimensions: 98 x 52 x 27 mm
Operating temperature: -25 - +75°C
With various digital I/O functions, the ETH-MOD series is an IP-based Ethernet I/O monitoring and control module. The module can be controlled remotely via Ethernet network using Modbus/TCP protocol. This makes the ETH-MOD series perfect integration with HMI, SCADA, PLC and other software systems.
The functionality of the ETH-MOD series is almost the same as the ETHIOxx series. ETH-MOD is the mini Ethernet I/O modules of the series which support various I/O types, such as Photoisolated digital input, relay contact. The module can be used to create a DI to DO-pair connection via Ethernet. Once the configuration is complete, the ETH-MOD serial module can tune the status of the local DI channels and then use the Modbus / TCP protocol to continuously write to an external DO device in the background.
ETH-MOD has double watchdog which automatically resets itself when the built-in firmware runs abnormally. The host watchdog monitors the host controller (PC or PLC) and the output of the module can go to predefined state (safe value) when the host fails.
For maximum space savings, the ETH-MOD series is offered in an amazingly small form factor that makes it easy to install anywhere, even directly embedded in a machine. It is equipped with two removable terminal block connectors for easy connection and has a powerful 32-bit ARM MCU.
16 digitale indgange med isolation, fælles stel. med PoE
Network module with digital I / O Korenix JETI / O 6550
Channels: 14/8
Digital inputs: 14 pcs., Logic 0: 0 - 4 V, Logic 1: 5 - 30V
Digital outputs: & nbsp; 8 pcs. Open collector, 5 - 40 V 250mA
Isolation: Optical 2500 VRMS for analog and digital inputs and outputs for the power supply
Magnetic 1500 V from the network interface for the power supply
10/100 Mbit m / RJ45 their connector
Operating temperature: - 25 ° C - 70 ° C
Supports Modbus / TCP, OPC server, SNMP. Software included for configuration
For DIN rail mounting
Supply: 10 - 30 VDC via terminal block, Max 1.92 W
Built-in Web server
Web HMI
Modbus / TCP and Modbus / UDP protocols
Good communication security
Dual Watchdog
Operating temperature range: -25 ~ + 75 ° C
I/O Pair-link - the input is mirrored in the other's output
6 x Analog inputs: 500mV +/- - +/- 10 V, 0 - 20mA (16bit)
2 x Analog outputs: 0 - +/- 10VDC, 0 - 20mA (12bit)
10 samples per second
2 x Digital input (count): Wet / Dry, max. + 30VDC (100Hz)
2 x Digital outputs: Open Collector, max. 50VDC / 700mA
2 x RJ45 Ethernet
Supply voltage: 10 - 30VDC / 4Watt
Modbus / TCP I / O module with built-in Web server
Modbus / TCP and Modbus / UDP protocols
2 x RJ45 Ethernet switch to Daisy-Chain topology
Dual Watchdog
Operating temperature range: - 25 to + 75 ° C
I / O Pair connection - Ingang refles in the second's exit
8 x Digital input: Wet (Apply Volt), Dry (Contact) - Digital Input: 0 - + 50CDC or Open / GND
8 x Digital Outout, Open Collector 0 - 40VDC / 650MA
Dimensions: 76 mm x 120 mm x 38 mm
Supply voltage: 12 - 48vdc, 4 watt
your bracket Wall mounting
