GSM / LTE alarm - 4G
Configuration via USB (Windows program) or SMS
2 x digital inputs with "dry contact" or "logic level" mode
2 x analog input from 0 to 60VDC, 10 bits
2 x relay output with NO / NC switches
1-Wire interface for 4 Teracom temperature and humidity sensors
Input can be navigated with alarm text etc.
SMS alarm - up to 5 numbers
Email alarm - up to 5 email recipients, SMTP with TLS support
1 relay can be activated with calls from up to 100 telephone numbers
Push mode - XML data is sent via HTTP Post to a remote server. Server response may include relay setup.
MQTT 3.1.1 support
Firmware update "on air"
Supply voltage: 8 - 32VDC, 2Watt - additional PSU
Dimensions: 109 x 65 x 32 mm
Weight: 152g
TCG120 is an I/O controller with GSM remote monitoring and control via mobile network. It has two digital inputs, two analog inputs. Its 1-Wire interface supports up to 4 Teracom humidity and temperature sensors. It's two relays have normally open and normally closed contacts.
The relays can be activated either externally (via SMS or HTTP response from external server) or locally - from the status of the monitored parameter. Only one parameter can control the relay at the same time, but for each parameter an e-mail or SMS can be sent to the alarm administrator.
TCG120 can initiate a connection (HTTP mail) to the remote dedicated servers - XML file, with current values for monitored parameters.
HTTP mail can be sent periodically or upon preset alarm conditions. The server can then respond with relay setup (see the manual under "Downloads"). This is very useful in client-server systems for GSM-GPRS remote monitoring and control
The controller can be used as a stand-alone unit or as part of data monitoring systems (SCADA).
Mains adapter - switch mode type
110-240 VAC to 12VDC/1.5A
DC plug: 5.5/2.1 mm
1 meter cable
Switch mode type
110-240 VAC for & nbsp; 12VDC / 3A
DC connector: 5.5 / 2.1 mm
USB 2.0 kabel beregnet til mini USB standard, 28 AWG.
Forhandles i forskellige længder.
Temperature and humidity sensor
1-wire interface for Teracom controller
Temperature: +/-0.4 °C (-10 to +60 °C), max. +/-0.6°C
Resolution: 0.1°C
Humidity: +/-3.0% RH (20 - 80% RH), max. +/-5% relative humidity
Solution: 0.1% RH
Supply voltage: 4.5 - 26VDC
LED indicator for communication status
Long-term stability based on digital signal processing
Changeable bit rate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Combination sensor for temperature and humidity measurement
Modbus RTU
2 x RJ45 connector - with daisy chain to the next module
RS485 Bus to Controller.
Up to 32 devices can be connected Controller
3.0% relative humidity measurement accuracy
12 bit resolution for humidity measurement
14 bit resolution for temperature measurement
With the mounting flanges
Excellent long term stability
Each module has its own ID code
Multi sensor for CO2 and Barometric pressure
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA
Temperature and Humidity sensor
RS485 MODBUS RTU
Temperature: +/-0,4 °C (-10 to +60°C), max. +/-0,6°C
Resolution: 0,1°C
Humidity: +/-3,0% RH (20 - 80% RH), max. +/-5% RH
Resolution: 0,1% RH
Supply voltage: 4,5 - 26VDC
LED indicator for status of communication
Long-term stability based on digital signal processing
RS-485 interface (2-wire) carrying up to 32 nodes
Changeable bitrate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
